||= Version =||= MinHW =||= Date =||= Done by =||= Reason =|| ||2.00 || ||2012/09/25 ||martin.vdeventer || EMC and EMI Test qualification firmware for RF Wallstat and RF Access Point || ||2.04 || ||2012/09/28 ||martin.vdeventer || EMC and EMI Test qualification firmware for RF Wallstat and RF Access Point || || || || || || Permanent carrier WS and AP || ||3.00 || ||2012/10/05 ||martin.vdeventer || EMC and EMI Test qualification firmware for RF Wallstat and RF Access Point || || || || || || 0 - OFF || || || || || || 1 - 868.050MHz || || || || || || 2 - 868.150MHz || || || || || || 3 - 868.250MHz || || || || || || 4 - 868.350MHz || || || || || || 5 - 868.450MHz || || || || || || 6 - 868.550MHz || ||4.00 || ||2012/11/20 ||martin.vdeventer || Port to new MSP430F5328 CODEB_ISR msp430 delay cross_studio_io print puts || ||4.01 || ||2012/11/20 ||martin.vdeventer || NOTE: 1 must be for (i = 0; i < SegCnt; i++) and not for (i = 0; i < SegCnt; SegCnt++) || ||4.02 || ||015/07/06 ||martin.vdeventer || itial Code for new Rickard RF WALLSTAT and ACCESSPOINT || ||4.03 || ||2015/08/18 ||martin.vdeventer || AP PDO for TC 6 added || || || || || || save to flash MFRI network on AP. Load from ram || || || || || || button press to initiate join || || || || || || Note 1: Changed in bsp_board.c "BSP_TIMER_CLK_MHZ*usec;" to "32 *usec;" || ||4.04 || ||2015/10/09 ||martin.vdeventer || Working 15 Wallstats but with uMsg Comms still iffy if Link Mode || ||4.05 || ||2015/10/09 ||martin.vdeventer || NOTE: 2 Changed LINKLISTEN_MILLISECONDS_2_WAIT from 5000 to 100 and || || || || || || Solved uMsg Comms fail when Linking || ||4.06 || ||2015/11/13 ||martin.vdeventer || NOTE 3: Can not increment counter here, will cause poll to skip Onboard MAster || ||4.07 || ||2016/05/19 ||martin.vdeventer || Add RSSI and Battery Volts SDO's for RF Wallstat on AP and RSSI display on RF Wallstat || ||4.08 || ||2016/05/19 ||martin.vdeventer || Immediate Peer Address Save to RAM when device receive's link from ED || || || || || || Add VCC and RSSI PDO FC 5 to RF Wallstat || ||4.09 || ||2016/05/26 ||martin.vdeventer || NOTE: 4.09.1 Fix the reset/startup hang added XT1HFOFFG in flags to clear and also added delay || || || || || || before checking and clearing the flags again || || || || || || NOTE: 4.09.2 Poll the wallstats as they come in || || || || || || NOTE: 4.09.3 Add the RF ED_TYPE and RF ED_FW_VER also to the PDO out of the WALLSTAT || ||4.10 || ||2016/06/09 ||martin.vdeventer || Add chang over cope to other WS from enabled wallstat change over || ||4.17 || ||2016/09/29 ||martin.vdeventer || Update Frequency from 868.150MHZ with 150KHz steps and 7 channels. || ||4.18 || ||2017/02/10 ||martin.vdeventer || //REMOVED: NOTE: 4.09.2 Poll the wallstats as they come in || ||4.19 || ||2017/02/24 ||martin.vdeventer || //Just some code mods || || || || || || Various Firmware updates || || || || || || Enable Setpoint display on WS || || || || || || 1 minute interval transmit from WS if temp spec for heating or cooling met || || || || || || 10 minute maximum transmit interval || || || || || || implemented SDO 50 read for virtual WS on AP || ||4.20 ||2 ||2017/02/24 ||martin.vdeventer || Changed RF_COMMS_TX_INTERVAL_MAX from 30 to 660 seconds || ||4.21 ||2 ||2017/02/24 ||martin.vdeventer || Changed RF_COMMS_TX_INTERVAL_MAX from 660 to 660*2 seconds || ||4.22 ||2 ||2017/04/04 || || NOTE: 11 NWK_REPLY_DELAY(); x 4 to solve missing packets || ||4.23 ||2 ||2017/04/04 || || NOTE: 11 NWK_REPLY_DELAY(); x 1 to solve missing packets || ||4.24 ||2 ||2017/06/27 ||martin.vdeventer || NOTE: 12 Disable Temp copy to CO || ||4.25 ||2 ||2017/07/16 ||martin.vdeventer || NOTE: 13 Disable CO by default || ||4.26 ||2 ||2017/08/23 ||martin.vdeventer || NOTE: 14 if no serial then loop must be 0 || ||4.27 ||2 ||2017/08/23 ||martin.vdeventer || NOTE: 15 Commissioning mode || || || || || || NOTE: 16 Send back the Min and Max Setpoint to RF device || || || || || || NOTE: 17 This is to ensure that the setpoint is in limitswhen recevied via poll from end device || || || || || || NOTE: 18 Each time a message is received from ED the MIN and MAX SP to ED wil be aupdated || ||4.28 ||2 ||2017/09/06 ||martin.vdeventer || changed RF_COMMISSION_TIME to 30 minutes = 1800seconds || ||4.29 ||2 ||2017/09/12 ||martin.vdeventer || change VOLTAGE_LOW_2_6 to VOLTAGE_LOW_2_8V || ||4.30 ||2 ||2017/09/15 ||martin.vdeventer || Added SDO 63 Commision Mode Timeout || ||4.31 ||2 ||2017/10/05 ||martin.vdeventer || NOTE: 18 Change Over must be default 0 || || || || || || NOTE: 19 default all NodeInfo values here || ||4.32 ||2 ||2017/10/18 ||martin.vdeventer || NOTE: 20 Add Vcc/Rssi/Timeout to Wallstat PDO in byte 8 of PDO || || || || || || ICASA EMC TESTS FOR 920MHZ AP WS POD || ||4.33 ||2 ||2017/11/14 ||martin.vdeventer || NOTE: 21 Bootloader update || || || || || || || || || || || || || ||4.34 ||2 ||2017/11/16 ||martin.vdeventer || NOTE: 22 || || || || || || Split ProcDataAP and ProcdataWS || || || || || || ProcDataAP to InfoB || || || || || || ProcDataWS to PROCDATA || ||4.35 ||2 ||2017/11/23 ||martin.vdeventer || NOTE 20: cahnge Comm time out flag to set when 60s more than EDCommsTimeMax || ||4.36 ||2 ||2018/03/05 ||martin.vdeventer || CONFIRMED EIRP levels at ISERT for 920MHZ to be below 3mW || ||4.37 6.37 ||2 ||2018/03/20 ||martin.vdeventer || 868MHz release firmware || || || || || || Added support for compile time for FW_VERSION to be 4.xx for 868MHz and 6.xx for 920MHz || || || || || || Added FIRMWARE_868_MAJOR || || || || || || Added FIRMWARE_920_MAJOR || || || || || || Added FIRMWARE_MINOR || ||4.38 6.38[[BR]] ||2 ||2018/08/28 ||martin.vdeventer || Add reset again when there is no Diffuser Controller || ||4.39 6.39 ||2 ||2018/09/13 ||martin.vdeventer || Dont write to flash when erasing or refreshing network. Make the commission mode for 1 hour instead of 30min.[[BR]] || ||4.40 6.40 ||2 ||2018/09/17 ||martin.vdeventer ||enable watchdog timer again||