| 1 | | WIP |
| | 1 | ||= Version =||= MinHW =||= Date =||= Done by =||= Reason =|| |
| | 2 | || 6.00||4|| 2011/11/22 ||mvdeventer ||New version 4 hardware || |
| | 3 | || 6.03||4|| 2012/12/05 ||mvdeventer ||Updates for Lighting Control with wired light switch \\ Only do I2C comms (occupancy and flow) when the slave comms is idle|| |
| | 4 | || 6.04||4|| 2013/13/01 ||mvdeventer ||In chip Command Added again \\ Fix I2C comms sync \\ Add flow sensor functions || |
| | 5 | || 6.05||4||2013/26/02 ||mvdeventer ||Improve I2C occupancy comms \\Enable WDT, was off for debug \\ Rework Flow averaging calculation \\!LightSwitchChipIn - send occupancy status PDO immediately \\ Add overide indication\\ Remove Stratification mode again || |
| | 6 | || 6.06||4||2013/26/02 ||mvdeventer ||Add sdo to read occupancy sensor identification info || |
| | 7 | || 6.07||4||2013/26/02 ||mvdeventer ||Disable motor before reboot, to ensure that all motor off during a software update|| |
| | 8 | || 6.08||4||2013/05/22 ||mvdeventer ||Update bootloader to disable motor, to ensure that the motor is not drawing current in boot loader mode\\Rework the watchdog timer|| |
| | 9 | || 6.09||4||2013/05/22 ||mvdeventer ||**Recalled** control did not work\\ change occ sensitivity from 6 to 8 || |
| | 10 | || 6.10||4||2014/02/24 ||mvdeventer ||Fix 6.09 \\ Add intelligent (I2C) heater functionality, ensure the heater minimum on value is 10% \\ Add SDO 35 36 37 for flow control from MCU || |
| | 11 | || 6.11||4||2014/03/30 ||mvdeventer ||Add heater control bits, Control / Status heater control bits \\ Restore WDT || |
| | 12 | || 6.12||4||2014/06/06 ||mvdeventer ||Add Occupancy enable/disable(present) and Occupancy detected \\ Add Flow detected(sensor connected) || |
| | 13 | || 6.13||4||2014/06/06 ||mvdeventer ||Fix flow if no occupancy sensor is connected || |
| | 14 | || 6.14||4||2015/01/19 ||mvdeventer ||Correcty handle 0Pa reading from flow sensor \\ Don't do Control Override on Zone 0 || |
| | 15 | || 6.15||4||2016/09/28 ||christo.malan ||Add heater control and other change over modes DM0073-0014 || |
| | 16 | || 6.16||4||2017/11/13 ||mvdeventer ||Added valve control for 24VAC Valves || |
| | 17 | || 6.17||4||2019/07/25 ||christo.malan ||Stagger MotorInit, prevent motors from hitting endstop all at the same time || |
| | 18 | || 6.18||4||2019/11/19 ||christo.malan ||Add flow offset SDO || |
| | 19 | || 6.19||4||2020/02/17 ||mvdeventer ||Stability improvements for I2C code (Flow and Occupancy) \\ Rolling average on Flow/pressure value \\ Add ResetFlow cmd on flow sensor error|| |
| | 20 | || 6.20||4||2020/04/02 ||christo.malan ||Remove flow updates from 6.19 \\ Disable button if pressed at startup. \\ Add sdo to show if it is disabled || |
| | 21 | || 6.21||4||2020/06/22 ||christo.malan ||Add flow updates from 6.19 || |
| | 22 | || 6.22||4||2020/07/24 ||christo.malan ||Clear flow connected flag if no sensor is connected \\ Add pressure test sdo 65 || |
| | 23 | || 6.23||4||2021/03/18 ||christo.malan ||Add network lock \\Remove OCC chip in \\ Save button disable state in flash|| |
