| Version | MinHW | Date | Done by | Reason
|
|---|
| 2.00 | | 2012/09/25 | martin.vdeventer | EMC and EMI Test qualification firmware for RF Wallstat and RF Access Point
|
| 2.04 | | 2012/09/28 | martin.vdeventer | EMC and EMI Test qualification firmware for RF Wallstat and RF Access Point
|
| | | | | Permanent carrier WS and AP
|
| 3.00 | | 2012/10/05 | martin.vdeventer | EMC and EMI Test qualification firmware for RF Wallstat and RF Access Point
|
| | | | | 0 - OFF
|
| | | | | 1 - 868.050MHz
|
| | | | | 2 - 868.150MHz
|
| | | | | 3 - 868.250MHz
|
| | | | | 4 - 868.350MHz
|
| | | | | 5 - 868.450MHz
|
| | | | | 6 - 868.550MHz
|
| 4.00 | | 2012/11/20 | martin.vdeventer | Port to new MSP430F5328 CODEB_ISR msp430 delay cross_studio_io print puts
|
| 4.01 | | 2012/11/20 | martin.vdeventer | NOTE: 1 must be for (i = 0; i < SegCnt?; i++) and not for (i = 0; i < SegCnt?; SegCnt?++)
|
| 4.02 | | 015/07/06 | martin.vdeventer | itial Code for new Rickard RF WALLSTAT and ACCESSPOINT
|
| 4.03 | | 2015/08/18 | martin.vdeventer | AP PDO for TC 6 added
|
| | | | | save to flash MFRI network on AP. Load from ram
|
| | | | | button press to initiate join
|
| | | | | Note 1: Changed in bsp_board.c "BSP_TIMER_CLK_MHZ*usec;" to "32 *usec;"
|
| 4.04 | | 2015/10/09 | martin.vdeventer | Working 15 Wallstats but with uMsg Comms still iffy if Link Mode
|
| 4.05 | | 2015/10/09 | martin.vdeventer | NOTE: 2 Changed LINKLISTEN_MILLISECONDS_2_WAIT from 5000 to 100 and
|
| | | | | Solved uMsg Comms fail when Linking
|
| 4.06 | | 2015/11/13 | martin.vdeventer | NOTE 3: Can not increment counter here, will cause poll to skip Onboard MAster
|
| 4.07 | | 2016/05/19 | martin.vdeventer | Add RSSI and Battery Volts SDO's for RF Wallstat on AP and RSSI display on RF Wallstat
|
| 4.08 | | 2016/05/19 | martin.vdeventer | Immediate Peer Address Save to RAM when device receive's link from ED
|
| | | | | Add VCC and RSSI PDO FC 5 to RF Wallstat
|
| 4.09 | | 2016/05/26 | martin.vdeventer | NOTE: 4.09.1 Fix the reset/startup hang added XT1HFOFFG in flags to clear and also added delay
|
| | | | | before checking and clearing the flags again
|
| | | | | NOTE: 4.09.2 Poll the wallstats as they come in
|
| | | | | NOTE: 4.09.3 Add the RF ED_TYPE and RF ED_FW_VER also to the PDO out of the WALLSTAT
|
| 4.10 | | 2016/06/09 | martin.vdeventer | Add chang over cope to other WS from enabled wallstat change over
|
| 4.17 | | 2016/09/29 | martin.vdeventer | Update Frequency from 868.150MHZ with 150KHz steps and 7 channels.
|
| 4.18 | | 2017/02/10 | martin.vdeventer | REMOVED: NOTE: 4.09.2 Poll the wallstats as they come in
|
| 4.19 | | 2017/02/24 | martin.vdeventer | Just some code mods
|
| | | | | Various Firmware updates
|
| | | | | Enable Setpoint display on WS
|
| | | | | 1 minute interval transmit from WS if temp spec for heating or cooling met
|
| | | | | 10 minute maximum transmit interval
|
| | | | | implemented SDO 50 read for virtual WS on AP
|
| 4.20 | 2 | 2017/02/24 | martin.vdeventer | Changed RF_COMMS_TX_INTERVAL_MAX from 30 to 660 seconds
|
| 4.21 | 2 | 2017/02/24 | martin.vdeventer | Changed RF_COMMS_TX_INTERVAL_MAX from 660 to 660*2 seconds
|
| 4.22 | 2 | 2017/04/04 | | NOTE: 11 NWK_REPLY_DELAY(); x 4 to solve missing packets
|
| 4.23 | 2 | 2017/04/04 | | NOTE: 11 NWK_REPLY_DELAY(); x 1 to solve missing packets
|
| 4.24 | 2 | 2017/06/27 | martin.vdeventer | NOTE: 12 Disable Temp copy to CO
|
| 4.25 | 2 | 2017/07/16 | martin.vdeventer | NOTE: 13 Disable CO by default
|
| 4.26 | 2 | 2017/08/23 | martin.vdeventer | NOTE: 14 if no serial then loop must be 0
|
| 4.27 | 2 | 2017/08/23 | martin.vdeventer | NOTE: 15 Commissioning mode
|
| | | | | NOTE: 16 Send back the Min and Max Setpoint to RF device
|
| | | | | NOTE: 17 This is to ensure that the setpoint is in limitswhen recevied via poll from end device
|
| | | | | NOTE: 18 Each time a message is received from ED the MIN and MAX SP to ED wil be aupdated
|
| 4.28 | 2 | 2017/09/06 | martin.vdeventer | changed RF_COMMISSION_TIME to 30 minutes = 1800seconds
|
| 4.29 | 2 | 2017/09/12 | martin.vdeventer | change VOLTAGE_LOW_2_6 to VOLTAGE_LOW_2_8V
|
| 4.30 | 2 | 2017/09/15 | martin.vdeventer | Added SDO 63 Commision Mode Timeout
|
| 4.31 | 2 | 2017/10/05 | martin.vdeventer | NOTE: 18 Change Over must be default 0
|
| | | | | NOTE: 19 default all NodeInfo? values here
|
| 4.32 | 2 | 2017/10/18 | martin.vdeventer | NOTE: 20 Add Vcc/Rssi/Timeout? to Wallstat PDO in byte 8 of PDO
|
| | | | | ICASA EMC TESTS FOR 920MHZ AP WS POD
|
| 4.33 | 2 | 2017/11/14 | martin.vdeventer | NOTE: 21 Bootloader update
|
| | | | | <MemorySegment? size="0x6000" to size="0x6400" access="Read" start="0x8000" name="FLASH"/>
|
| | | | | <MemorySegment? size="0x400 " to size="0x800 " access="Read" start="0xE800" to start="0xE400" name="PROCDATA"/>
|
| 4.34 | 2 | 2017/11/16 | martin.vdeventer | NOTE: 22
|
| | | | | Split ProcDataAP and ProcdataWS
|
| | | | | ProcDataAP to InfoB
|
| | | | | ProcDataWS to PROCDATA
|
| 4.35 | 2 | 2017/11/23 | martin.vdeventer | NOTE 20: cahnge Comm time out flag to set when 60s more than EDCommsTimeMax
|
| 4.36 | 2 | 2018/03/05 | martin.vdeventer | CONFIRMED EIRP levels at ISERT for 920MHZ to be below 3mW
|
| 4.37 6.37 | 2 | 2018/03/20 | martin.vdeventer | 868MHz release firmware
|
| | | | | Added support for compile time for FW_VERSION to be 4.xx for 868MHz and 6.xx for 920MHz
|
| | | | | Added FIRMWARE_868_MAJOR
|
| | | | | Added FIRMWARE_920_MAJOR
|
| | | | | Added FIRMWARE_MINOR
|
| 4.38 6.38 | 2 | 2018/08/28 | martin.vdeventer | Add reset again when there is no Diffuser Controller
|
| 4.39 6.39 | 2 | 2018/09/13 | martin.vdeventer | Dont write to flash when erasing or refreshing network. Make the commission mode for 1 hour instead of 30min.
|
