Version	MinHW	Date	Done by	Reason
2.00		2012/09/25	martin.vdeventer	EMC and EMI Test qualification firmware for RF Wallstat and RF Access Point
2.04		2012/09/28	martin.vdeventer	EMC and EMI Test qualification firmware for RF Wallstat and RF Access Point
				Permanent carrier WS and AP
3.00		2012/10/05	martin.vdeventer	EMC and EMI Test qualification firmware for RF Wallstat and RF Access Point
				0 - OFF
				1 - 868.050MHz
				2 - 868.150MHz
				3 - 868.250MHz
				4 - 868.350MHz
				5 - 868.450MHz
				6 - 868.550MHz
4.00		2012/11/20	martin.vdeventer	Port to new MSP430F5328 CODEB_ISR msp430 delay cross_studio_io print puts
4.01		2012/11/20	martin.vdeventer	NOTE: 1 must be for (i = 0; i < SegCnt?; i++) and not for (i = 0; i < SegCnt?; SegCnt?++)
4.02		015/07/06	martin.vdeventer	itial Code for new Rickard RF WALLSTAT and ACCESSPOINT
4.03		2015/08/18	martin.vdeventer	AP PDO for TC 6 added
				save to flash MFRI network on AP. Load from ram
				button press to initiate join
				Note 1: Changed in bsp_board.c "BSP_TIMER_CLK_MHZ*usec;" to "32 *usec;"
4.04		2015/10/09	martin.vdeventer	Working 15 Wallstats but with uMsg Comms still iffy if Link Mode
4.05		2015/10/09	martin.vdeventer	NOTE: 2 Changed LINKLISTEN_MILLISECONDS_2_WAIT from 5000 to 100 and
				Solved uMsg Comms fail when Linking
4.06		2015/11/13	martin.vdeventer	NOTE 3: Can not increment counter here, will cause poll to skip Onboard MAster
4.07		2016/05/19	martin.vdeventer	Add RSSI and Battery Volts SDO's for RF Wallstat on AP and RSSI display on RF Wallstat
4.08		2016/05/19	martin.vdeventer	Immediate Peer Address Save to RAM when device receive's link from ED
				Add VCC and RSSI PDO FC 5 to RF Wallstat
4.09		2016/05/26	martin.vdeventer	NOTE: 4.09.1 Fix the reset/startup hang added XT1HFOFFG in flags to clear and also added delay
				before checking and clearing the flags again
				NOTE: 4.09.2 Poll the wallstats as they come in
				NOTE: 4.09.3 Add the RF ED_TYPE and RF ED_FW_VER also to the PDO out of the WALLSTAT
4.10		2016/06/09	martin.vdeventer	Add chang over cope to other WS from enabled wallstat change over
4.17		2016/09/29	martin.vdeventer	Update Frequency from 868.150MHZ with 150KHz steps and 7 channels.
4.18		2017/02/10	martin.vdeventer	REMOVED: NOTE: 4.09.2 Poll the wallstats as they come in
4.19		2017/02/24	martin.vdeventer	Just some code mods
				Various Firmware updates
				Enable Setpoint display on WS
				1 minute interval transmit from WS if temp spec for heating or cooling met
				10 minute maximum transmit interval
				implemented SDO 50 read for virtual WS on AP
4.20	2	2017/02/24	martin.vdeventer	Changed RF_COMMS_TX_INTERVAL_MAX from 30 to 660 seconds
4.21	2	2017/02/24	martin.vdeventer	Changed RF_COMMS_TX_INTERVAL_MAX from 660 to 660*2 seconds
4.22	2	2017/04/04		NOTE: 11 NWK_REPLY_DELAY(); x 4 to solve missing packets
4.23	2	2017/04/04		NOTE: 11 NWK_REPLY_DELAY(); x 1 to solve missing packets
4.24	2	2017/06/27	martin.vdeventer	NOTE: 12 Disable Temp copy to CO
4.25	2	2017/07/16	martin.vdeventer	NOTE: 13 Disable CO by default
4.26	2	2017/08/23	martin.vdeventer	NOTE: 14 if no serial then loop must be 0
4.27	2	2017/08/23	martin.vdeventer	NOTE: 15 Commissioning mode
				NOTE: 16 Send back the Min and Max Setpoint to RF device
				NOTE: 17 This is to ensure that the setpoint is in limitswhen recevied via poll from end device
				NOTE: 18 Each time a message is received from ED the MIN and MAX SP to ED wil be aupdated
4.28	2	2017/09/06	martin.vdeventer	changed RF_COMMISSION_TIME to 30 minutes = 1800seconds
4.29	2	2017/09/12	martin.vdeventer	change VOLTAGE_LOW_2_6 to VOLTAGE_LOW_2_8V
4.30	2	2017/09/15	martin.vdeventer	Added SDO 63 Commision Mode Timeout
4.31	2	2017/10/05	martin.vdeventer	NOTE: 18 Change Over must be default 0
				NOTE: 19 default all NodeInfo? values here
4.32	2	2017/10/18	martin.vdeventer	NOTE: 20 Add Vcc/Rssi/Timeout? to Wallstat PDO in byte 8 of PDO
				ICASA EMC TESTS FOR 920MHZ AP WS POD
4.33	2	2017/11/14	martin.vdeventer	NOTE: 21 Bootloader update
				<MemorySegment? size="0x6000" to size="0x6400" access="Read" start="0x8000" name="FLASH"/>
				<MemorySegment? size="0x400 " to size="0x800 " access="Read" start="0xE800" to start="0xE400" name="PROCDATA"/>
4.34	2	2017/11/16	martin.vdeventer	NOTE: 22
				Split ProcDataAP and ProcdataWS
				ProcDataAP to InfoB
				ProcDataWS to PROCDATA
4.35	2	2017/11/23	martin.vdeventer	NOTE 20: cahnge Comm time out flag to set when 60s more than EDCommsTimeMax
4.36	2	2018/03/05	martin.vdeventer	CONFIRMED EIRP levels at ISERT for 920MHZ to be below 3mW
4.37 6.37	2	2018/03/20	martin.vdeventer	868MHz release firmware
				Added support for compile time for FW_VERSION to be 4.xx for 868MHz and 6.xx for 920MHz
				Added FIRMWARE_868_MAJOR
				Added FIRMWARE_920_MAJOR
				Added FIRMWARE_MINOR
4.38 6.38	2	2018/08/28	martin.vdeventer	Add reset again when there is no Diffuser Controller
4.39 6.39	2	2018/09/13	martin.vdeventer	Dont write to flash when erasing or refreshing network. Make the commission mode for 1 hour instead of 30min.
4.40 6.40	2	2018/09/17	martin.vdeventer	enable watchdog timer again