Version	MinHW	Date	Done by	Reason
2.00	A	2012/09/25	martin.vdeventer	EMC and EMI Test qualification firmware for RF Wallstat and RF Access Point
2.03	A	2012/09/25	martin.vdeventer	Permanent Carrier Transmit
3.00	A	2012/10/05	martin.vdeventer	EMC and EMI Test qualification firmware for RF Wallstat and RF Access Point
				0 - OFF
				1 - 868.050MHz
				2 - 868.150MHz
				3 - 868.250MHz
				4 - 868.350MHz
				5 - 868.450MHz
				6 - 868.550MHz
4.00	A	2013/10/24	martin.vdeventer	Remove UP button reset interrupt and put back Setpoint edit mode
4.01	A	2014/08/21	martin.vdeventer	Add a low power mode with LCD
4.02	A	2016/02/11	martin.vdeventer	Added SETUP MENU: PRESS all four buttons simultaneously
				Added SETUP MENU: Added AP LINK ID set in SETUP MENU
				Added SETUP MENU: Added Delay for transmit interval from 0 to 10 minutes
				SMPL LINK INIT JOIN retry every 2 seconds with 2 seconds increments up to 20 seconds
				SMPL LINK LINK retry every 2 seconds with 2 seconds increments up to 20 seconds
				Transmit every delay HEARTBEAT setup in SETUP MENU with no ack
				Transmit every MESSAGE_POLL_TIMEOUT_FACTOR with ack a Poll to check for setpoint change
				If no ack is received for every 3rd poll then start to blink the RF sign
				If no ack is received for 10 polls then go into WDT sleep low power for WDTCOUNT* 2:15 minutes intervals(compile time)
4.03	A	2016/02/19		WS: Press All Four buttons to Exit low power sleep and start device for the first time
4.04	A	2016/03/08		WS: Interrupt driven exit and enter in LOW POWER MODES
4.05	A	2016/03/08		WS: SERIAL number as SimpliciTI address
4.06	A	2016/05/31		NOTE: 4.06.01 If device was set to SETPOINT EDIT and enter or menu then the device muste be retrigger RF COMMS
4.06	A	2016/06/20		Start Temperature timer and comparator in StateAppStartTempVcc? and stop in TIMER1_A1_ISR
4.10	A	2016/07/01		Low power with temp sample/battery sample and tranceive down to 65uS
				fixed the setpoint timeout and save with WDT
4.11	A	2016/07/01		Stop the WDT setpoint timout when exiting setpoint edit with menu or enter button
				Dynamic TX/RX interval...
				Cooling mode
				temp smaller than 0.5 deg cel above setpoint 0.1 deg cel delta 1 minute TX/RX
				temp bigger than 0.5 deg cel above setpoint 0.5 deg cel delta 1 minute TX/RX else every 10 min TX/RX
				Heating mode
				temp smaller than 1.5 deg cel below setpoint 0.1 deg cel delta 1 minute TX/RX
				temp bigger than 1.5 deg cel below setpoint 0.5 deg cel delta 1 minute TX/RX else every 10 min TX/RX
4.12	A	2016/09/29		Update Frequency from 868.150MHZ with 150KHz steps and 7 channels. Also update BSL txt file RFWallstatBSLProgram.txt
4.13	A	2017/02/14		Various Firmware updates
				Enable Setpoint display on WS
				1 minute interval transmit from WS if temp spec for heating or cooling met
				10 minute maximum transmit interval
				implemented SDO 50 read for virtual WS on AP
4.14	A	2017/02/28		Various Firmware updates
				#define VOLTAGE_LOW_2_8V 28 Minimum voltage is 2.8V
				and change battery low to 2.8V
4.15	A	2017/03/15		NOTE: 10 The radio does not go back to sleep after TX/RX sequence so this must be done to ensure LOW POWER
4.16	A	2017/03/22		various updates:
				Setup Menu Enable
				RTC Display Enable
				Setpoint Display Enable
				Setpoint edit Disable
4.17	A	2017/03/27		Implement 5 second menu with MENU key
				Implement 5 secend hidden menu with MENU/DOWN key
4.19	A	2017/04/04		NOTE: 11 NWK_REPLY_DELAY(); x 4 to solve missing packets
4.20	A	2017/04/06		NOTE: 11 NWK_REPLY_DELAY(); x 4 for WS to solve missing packets
				1 minute interrupt and TX every 10 minutes
				various mods
				BUG fixed that every 10 minute not TXing... FIXED SOMEHOW WITH CODE CLEANING
4.21	2	2017/04/06		#define DEFAULTS_AP_ADDRESS commented out
4.22	2	2017/04/10		Just some mods
4.23	2	017/04/22		WALLSTAT and REMOTE_TEMP_SENSOR is the same code but you must specify in the CrossStudio? build option for which one
				you want to compile for:
				END_DEVICE_WALLSTAT
				or
				END_DEVICE_TEMP_SENSOR
				Added debug code for Temp linearize---spicify with:
				DEBUGTEMP in system.h
4.24	2	2017/05/15		Only go into setup menu if the setup menu is enabled(Long press Menu key)
4.25	2	2017/09/05		NOTE: 15 Commissioning mode
				NOTE: 16 Min and Max Setpoint from AccessPoint?
				NOTE: 17 This is done to ensure that when you press up or down to edit SP TIME etc that eventually InterruptFlags? &= ~InterruptFlagGPIO gets cleared
4.26	2	2017/09/06	martin.vdeventer	removed debugging 1 seconds interrupt ALWAYS_USE_SECONDS_INTERRUPT
4.27	2	2017/09/14	martin.vdeventer	Able to control Second or Minute Interrupt from MLM APP
				Able to control MAX Comms Timeout from APP
4.28	2	2017/09/26	martin.vdeventer	NOTE: 18 Re-enable TransmitPermissionTime? in rtc_rfws.c
4.29	2	2017/09/26	martin.vdeventer	NOTE: 19 Linear estimate boundaries not set correctly in tempanalysis.c
4.30	2	2017/10/04	martin.vdeventer	NOTE: 20 Disable RFTESTMODE
4.31	2	2017/10/19	martin.vdeventer	NOTE: 21 Buzz 3 times when erasing AP address and going to sleep
4.32	2	2017/10/23	martin.vdeventer	NOTE: 22 Add RFTESTMODE for 920MHZ
				ICASA EMC TESTS FOR 920MHZ AP WS POD
4.33	2	2017/11/23	martin.vdeventer	868MHz Wallstat Normal
4.36	2	2018/03/05	martin.vdeventer	CONFIRMED EIRP levels at ISERT for 920MHZ to be below 3mW
4.37 6.37	2	2018/03/20	martin.vdeventer	868MHz release firmware
				Added support for compile time for FW_VERSION to be 4.xx for 868MHz and 6.xx for 920MHz
				Added FIRMWARE_868_MAJOR
				Added FIRMWARE_920_MAJOR
				Added FIRMWARE_MINOR
4.38 6.38	2	2018/08/03	martin.vdeventer	Ensure that WS does not reset when AP is lost and rather backoff for 10 minutes
				change RF_POLL_SETPOINT_EDIT_RETRY from 20 to 5
4.39 6.39	2	2018/08/07	martin.vdeventer	Refresh network did not work with 4.38 due to the fact that we were not resetting after AP disappears.
				ED will reset after a few retries when AP disappears.
				If AP disappears and ED resetted then the ED will try to communicate to AP every 10 minutes
				Unless button is pressed on ED then the ED will try to communicate within 10 seconds and then after that revert back to 10 minutes
4.40 6.40	2	2018/09/13	martin.vdeventer	Update LCD segment to display DS (Discovery) instead of SA (SHARE Address Mode
				If accessPoint is shut down during evening the ED wil Tx only every 10 minutes